Arkansas - Louisiana - Oklahoma - Texas

Arkansas
Flip Whitner
S&P Golf
8611 Hwy 107, Suite 106
Sherwood, AR
866-716-5333 Toll Free
501-835-5333 Phone
www.snpgolf.com
flip@whithog.com
Back to the top of the page

Louisiana
Michael Boatner - AGCP Level 5 Qualified & Certified
The Golf Club Shop
376 Windermere Blvd
Alexandria, LA 71303
318-201-4891
faybon@suddenlink.net

Kyle Chauvin
Chauvin Golf
322 Bergeron Loop
Carencro, LA 70520
337-258-6238
kylechauvin@aol.com

John Joy
N’JOY Golf LLC
PO Box 1166
Abbeville, LA 70511
337-344-0689
jrjoy@att.net
Back to the top of the page

Oklahoma
Ken Bodenhamer
Ken’s Klubs
7320 South Fulton Avenue
Tulsa OK 74136
Phone: 918-231-5137
Fax: 918-494-0643
ken@bodenhamer.com
GCA Accredited Clubmaker
Golfsmith Elite Member
Wishon Gold Plus Member
MOI Certified
Back to the top of the page

Texas
Keith Chatham - AGCP Master of Golf Club Technology
AGCP Charter Member
AGCP Lifetime Member
PrecisionFit Golf
1452 Sidney Baker
Kerrville, TX 78028
830-257-1234
website: www.precisionfitgolf.com
e-mail: pfg2003@gmail.com
Professional Clubmakers Society:
2006 PCS International Clubmaker of the Year
2006 PCS Regional Clubmaker of the Year
2005 PCS Regional Clubmaker of the Year
PCS Professional "Class A" Clubmaker
PCS Certified Clubfitter
PCS Certified Clubmaker
Golf Clubmakers Association:
2004-2005 Texas Clubmaker of the Year
GCA Accretited Professional Clubmaker
GCA Accretited Advanced Clubmaker
2007-2008 Texas Clubmaker of the Year

Jack Fisher – AGCP Level 7 Qualified & Certified
Pro Fit Golf
RETIRED
E-Mail: fish5er@mindspring.com
GCA Advanced Accredited Clubmaker

Lee Haines
Fair Oaks Ranch, TX
830-755-4848
fairway1@gvtc.com

Dave Murray
Plano Custom Clubs
5601 W Springcreek Parkway
Plano, TX 75024
972-517-3688
clubsmith50@hotmail.com

Mark Vallier - AGCP Level 10 Qualified & Certified
MK Golf LLC
13800 Jones Maltsberger
San Antonio TX
210-771-9360
mark.vallier@sbcglobal.net
PCS Professional "Class A" Clubmaker
GCA Accredited Professional Clubmaker
GCA Accredited Advanced Clubmaker
Wishon Gold Plus Member
FlightScope Launch Monitor Center
UST Tour Shop
Top 50 Accra Dealer 2007
Top 50 Accra Dealer 2008
FlightScope Launch Monitor Center
Matrix Shaft Partner
Graphite Design Shafts
Aldila Shafts
KBS Shaft Installation Center
Scratch Iron and Wedge Dealer
Back to the top of the page

Technical Terms:

BOUNCE
The amount of space between the leading edge and the groundline when the club is in the square address position. In general, more bounce is better for soft sand, lush grass and for golfers with a steeper angle of attack into the ball; less bounce is better for firm sand, short cropped turf and golfers with a more level angle of attack into the ball. A slight amount of bounce on all the irons is also helpful when playing on fairways of creeping type grasses typical in hot weather areas such as Bermuda or Kikuyu, etc.

BULGE
The face curvature from heel to toe on drivers and fairway woods. Bulge is required on all woodheads to offset the natural draw or fade action of the ball when impact occurs off center toward the toe (draw shot shape) or heel (fade shot shape) side of the face.

CAMBER or SOLE RADIUS
The radius measurement of the sole from front to back, or heel to toe.

CAST
Two Types of castings - see below

DIE CAST
A method of clubhead manufacture in which the molten metal from which the head is to be made is poured/injected directly into a hard steel mold. Die casting is typically used to make clubheads which are made of softer metals such as aluminum or zinc and used to make heads of lower cost or which do not have a high strength requirement, such as thick face aluminum woodheads, cheap low end ironheads or putter heads.